Home > Hard Drive > Installation Of Old ATA Hard Drive Into New Windows 8 Comp

Installation Of Old ATA Hard Drive Into New Windows 8 Comp

Contents

I guess I should have just given the very short answer that the drive RPM and Access times are independent of eah other...I'll be a little more careful in the future... BUY NOW FREE TRIAL UTILITIES PC Transfer » Todo PCTrans FreeDownload Todo PCTrans ProBuyTry Todo PCTrans TechnicianBuyTry Disk/Partition Copy » Disk Copy HomeDownload Disk Copy TechnicianBuy System Optimization CleanGenius for MacBuyTry I would like to use this computer to recover my data from a Samsung Spin Point (IDE) SV0813H, Hard Disk (XP) and a Seagate U Series 5 (IDE)ST340823A (ME) Hard Disk.How Reply curt on July 12, 2009 at 9:49 am You probably already figured it out…. have a peek here

Limit Capacity Option - This option may be required if the system the drive is being installing into does not support the full capacity of the drive. That does look perfect but unfortunately I'm in the UK and you can't get those on Amazon UK or eBay UK, so I've just gone for a generic USB case. Reply ian on December 26, 2008 at 2:19 am hi, nice step by step, but can you tell me how can i locate the slave hard drive when it is not Setting the Jumpers Master or Single Drive - Use this setting if the drive is the only drive on the ATA interface cable. https://www.eightforums.com/drivers-hardware/12569-installation-old-ata-hard-drive-into-new-windows-8-comp.html

Install Old Hard Drive In New Computer

The problem is that SATA is new, and the fine details of how it works still vary from motherboard to motherboard; hence, on some motherboards it is possible to have a A wizard will pop up and walk you through this process. There's no way that I know of to make those printers work with Windows 10 if there's no driver. For that reason, I'm going to suggest that you install your old PATA hard drive on the secondary controller, along with one optical drive.

The first hard drive is SATA, the second which came from an older computer is IDE. Even I could understand it………… Once again, many thanks. i changed the primary drive in the bios to the ide hard drive , still couldnt get passed start up mode. Adding Old Hard Drive To New Computer Can I replace the 6g with the 40 safely.

Thanks again. Move Hard Drive From One Computer To Another In addition I had to purchase a PCI serial ATA host controller card with a cable to connect the new HD. Congratulations! This connects to the new PC either by USB or Firewire.

Once you're done copying the files you want to keep, you can leave the old hard drive in the new machine, reformat it if you like, and have that much extra disk space Swapping Hard Drives Between Computers I don't know if that was the cheap way for the pc to set the hd as the master, but, since I had to add my old ide connector to be What about if you have a IDE hard drive and you upgraded it with a SATA adapter? This will prevent frustrations about losing programs after you have already formatted your computer.If you are simply installing a secondary hard drive for storage, you don't have to make any changes

Move Hard Drive From One Computer To Another

If you haven't already done so, shut down your new machine normally; then physically remove the power plug from the back of the computer chassis. http://www.easeus.com/resource/install-ide-hard-drive.htm Should I simply add jumpers and format the second drive? Install Old Hard Drive In New Computer Stone received a Bachelor of Arts in journalism and a Master of Arts in communication studies from Northern Illinois University. Moving Hard Drive To New Computer Windows 10 Now, plug your new machine in and turn it on.

USAFRetJan 9, 2014, 12:28 AM Quackamo said: That does look perfect but unfortunately I'm in the UK and you can't get those on Amazon UK or eBay UK, so I've just navigate here Best solution is to use a tool like ''Bootit''! QuackamoJan 8, 2014, 11:10 PM Hi there, quick question:What will happen if I put an old 160GB HDD with Windows XP and riddled with viruses (parents' old HDD) into a new After the drive is secured then go ahead and connect the power and IDE cables. What Kind Of Power Connector Does A Floppy Disk Drive Typically Use?

Shut the machine off, pull the power plug out of the back of the old computer, and remove the computer access panel or cover. However, there is often a diagram on the top of the drive telling you how to set the jumpers, and if not there will certainly be instructions in your hard drive's Flag Permalink This was helpful (0) Collapse - Difference Bothers You? http://easylinkr.com/hard-drive/how-does-4k-sector-hard-drive-work-with-windows.php Reply Mark Jacobs (Team Leo) February 10, 2016 at 10:55 am If you want to use that disk yourself, there's really no need to wipe it.

Most boards have 2 channels while 4 is becoming more and more common at least on the higher end boards. Transfer Hard Drive To New Computer Without Reinstalling Windows Disruptive posting: Flaming or offending other usersIllegal activities: Promote cracked software, or other illegal contentOffensive: Sexually explicit or offensive languageSpam: Advertisements or commercial links Submit report Cancel report Track this discussion Bootit will then go into maintenance mode.

OK it (result may take some time)14.

You can upgrade to Windows 8 without having to buy a new hard drive or your can move the hard drive from your old Windows 7 system and use it with Someone who finds this page from Google who doesn't the difference between a a computer and an X-Box would never know what on earth IDE or SATA is, let alone what After finding your article, written so I could understand it, I gained the confidence I needed to do it. Can I Use My Old Harddrive In A New Computer Sorted things out.

Start with search, at the top of the page. So my question to the world is can I put the harddrive into another computor to restore lost files and possibally benifit from 1 computor - 2 hard drives. Sorry, there was a problem flagging this post. this contact form I am literate, but not geek (all the way) … I have a Dell GX 240 Tower with 1GB ram,and its a 1.2.GHZ pentium 4 system.

Configuring the BIOS Close your computer case and start your computer. both came from a dell computer. Reply Janine on August 16, 2007 at 6:28 pm Many thanks for the VERY SIMPLE step by step instructions for initializing a STA harddrive. Troubleshooting No hard drives show up: Do you have two drives on the cable?

Usually, the label side points up; mimic the boot drive. Reply Darklance on August 16, 2007 at 3:05 pm Thankyou for the info David.. Windows 10 Redstone 2 14894 Build Update Tutorial with ISO. 2016-08-01 17:18:23 Tracy King - Windows 10 Restone 2 14894 ISO is ready to be downloaded and installed for you. What is this?

the c drive that im using now as like no memary some one told me to stick them in my d/cd or my e/dvd/cd drive to keep them out of my Make sure the power is plugged in and everything is connected securely. Using the old drive to boot and connecting the new one as a slave, I see all of the files created by the restore disk.Did I get a bad drive or F2 to enter Setup Utility."Can anyone tell me what I'm doing wrong?

Chances are that you don't need to worry about this.