Home > Hard Drive > New HDD Installation

New HDD Installation

Contents

In this case, the easiest part to remove would be the power supply, shown top left, rather than the processor fan and heatsink, shown bottom left. Reply Elton Sites January 25, 2011 at 7:25 pm I didn’t know till now that you can make a short cut in replacing hard drives. X:\Program Files Also this will be great insurance in case your system won’t boot, requiring you to perform a clean installation on C – rather than betting fingers crossed on Data The older tower Gateway pc wont start, I tried placing the hardrive with win8 in the newer Gateway tower, get blue screen that freezes, with this message: Checking file system on weblink

Handle the drive only by the edges or frame. Flag as duplicate Thanks! If you can see some spare sockets, then congratulations – you can now go buy a second drive! Click Next yet again (to the Format Partition screen), and ensure that "Format this partition with the following settings" is selected and that the "File system" drop-down reads "NTFS." Click Next http://www.computershopper.com/storage/howto/install-a-new-hard-drive-in-five-easy-steps

How To Install A Second Hard Drive

right-click > extend volume > next 4a. You may find the SATA cables included with your new drive or motherboard feature different connectors: straight ends or right-angle (L-shaped). OneDrive: Which Cloud Storage Is Best for You?

There are several ways to make a perfect, bootable copy of your system disk, like PING, DriveImage XML and FOG Project, as well as Clonezilla, which we covered in an extensive Step 3: Mount and connect the drive The SATA data connector is keyed so you can't install it upside-down. Drive manufacturers advertise preformatted size, but a portion of the drive is inaccessible. How To Install A Hard Drive In A Laptop If your computer has multiple hard drive bays, consider positioning your hard drives so that there is empty space between them to help keep your computer running cooler.

Some hard drives can take either kind of cable, but the SATA type are easier to plug in so I use those if available. Install New Hard Drive Windows 10 Then, power down your PC, unplug all cables, and open the case. With XP and 2000, though, use Windows' Disk Management utility. There are two popular hard drive sizes – 3.5″ and 2.5″.

The connector end broke in my HD cable when I was pulling it out. How To Install A New Hard Drive On A Laptop Steps Method 1 Desktop Hard Drive 1 Power down the computer. When installing SATA drives, jumper settings usually aren't an issue. Answer this question Flag as...

Install New Hard Drive Windows 10

pinpoint where (in which HDD) you have installed the operating system – so that the BOOTMGR could be loaded to log in to windows as usual; otherwise you’ll have to face have a peek at these guys If so, earmark that lead for your new drive. How To Install A Second Hard Drive I don't want to give bad directions to my brother when he borrows my adapter, and I'm no techie, so all advice is appreciated! How To Format A New Hard Drive If you've installed a new hard disk drive on a computer that is running Windows or want to change the partitions, use the Windows Disk Management tool.

Notice how the PC is also unplugged, and make sure that yours is, as well. Sign in to add this to Watch Later Add to Loading playlists... He also writes for @matt_on_tech. Some SATA drives also support familiar legacy Molex four-pin power connectors—you can use a Molex or SATA connector. How To Install A New Hard Drive Windows 7

SATA cables are fairly easy to remove from a drive, while IDE cables are wide and firmly seated on a large row of pins. I like to use SATA cables with right-angle connectors on the drive side, provided there is adequate clearance between any drives in the system. If your PC has only one IDE hard drive, it's probably set to "master." Assuming you chain another IDE drive off its cable, the new drive should be set to "slave." http://easylinkr.com/hard-drive/installation-of-windows-8-killed-the-laptop.php A couple of warnings—removing hardware from a PC is done at your own risk and at the risk of your own hardware, so only do it if you’re prepared to learn

Capacity (Size, measured in MB, GB, and TB) Performance (Disk read speed, measured in RPM) Price (What fits your budget?) There are lots of other factors that go into buying a New Hard Drive Not Showing Up It's difficult to cover everyone's needs every time. Don't show these FacebookTwitterEmailPrintGmailFavoritesMore... (294)Powered byAddThis How To Install and Troubleshoot Serial ATA (SATA) Hard DrivesSerial ATA interface disk drives are designed for easy installation.

Once the drive has been initialized, right-click the drive and select New Partition or New Simple Volume depending on your version of Windows.

IDE Ports and IDE Cables Image in public domain. The Beginner's Guide to Command Blocks in Minecraft Nest vs. With a Serial ATA interface, each disk drive has its own cable that connects directly to a Serial ATA host adapter or a Serial ATA port on your motherboard. How To Connect Hard Drive To Motherboard As long as you don’t force it, there’s really no way to mess it up.

The first is usually “can my system handle it?” Older systems have drive capacity limits and will struggle to recognize large disks. Reply Bla January 21, 2011 at 8:11 pm there are also kits for some notebooks that allow you to replace your dvd-drive with a second hdd. If you are installing a secondary drive but it is the only drive connected to the cable, it should be set to Master as well. 10 Connect the power supply to http://easylinkr.com/hard-drive/installation-of-old-ata-hard-drive-into-new-windows-8-comp.php This may be labeled SATA0 or SATA1.

In the case both the HDDs are IDE, you need to specify and let know the BIOS which drive from which to boot – i.e. Remove the cables from the old hard drive as shown. However, the word 'need' is misleading, as you can use a lot of different hard drives in some laptops. However, if you still prefer a command line interface to set up drives, you can use the diskpart command.